- Where should a toilet be placed in a bathroom?
- Can you move plumbing on a concrete slab?
- What fall is required for toilet waste?
- Do plumbing vents have to go through the roof?
- How far can you move a toilet?
- How do you move plumbing in a bathroom?
- What is the best offset toilet flange?
- How far out from the wall is a toilet flange?
- How far can a toilet be from the soil stack?
- Can you move your toilet plumbing?
- Why use offset toilet flange?
- How does a cheater vent work?
- Can 2 toilets share a vent?
- How far can you move a toilet with an offset flange?
- How much does it cost to relocate a toilet?
- Can a toilet shower and sink share a vent?
- What happens if you don’t vent a toilet?
- Can a toilet drain have bends?
Where should a toilet be placed in a bathroom?
Try to place the toilet facing an open wall or door, if possible, rather than a fixture.
Generally, this will ensure enough clearance room in front of the toilet.
For other bathrooms, aim for a 30-inch front clearance space for the toilet..
Can you move plumbing on a concrete slab?
Under slab plumbing lines can be moved, but when it’s done in a finished space, the can be very dirty and somewhat expensive. … In most cases, a home constructed on a concrete slab has the main water line entering from the exterior the below the slab and then it comes up in a utility or laundry room.
What fall is required for toilet waste?
All above ground and below ground horizontal drainage pipes should be laid to an adequate gradient. Gradients from 1 in 40 to 1 in 110 will normally give adequate flow velocities. A gradient of 1 in 80 is suitable for commencing calculations for pipe schemes.
Do plumbing vents have to go through the roof?
If you can’t put the main stack through the roof, most local plumbing codes allow you to put it through a wall instead, but there are conditions. It must extend vertically past the top frame of the highest window in the house, and in some locations, it may even have to extend above the roof line.
How far can you move a toilet?
However, you can also move the toilet to a certain extent without having to change the waste line and stack. If your waste line has a diameter of 3 inches, you can place the toilet within six feet of your stack. The toilet can also be as far as 10 feet from your stack, if the diameter of the waste line is 4 inches.
How do you move plumbing in a bathroom?
How to Re-route Bathroom PlumbingStep 1: Design Around Floor Joist Locations. … Step 2: Determine Required Setback Measurements. … Step 3: Include Access Panels in Design. … Step 1: Cap Old Water Feeds. … Step 2: Install New Water Feeds. … Step 3: Ensure the Slope Is Correct. … Step 1: Pressurize New Water Feeds. … Step 2: Install New Bathroom Fixtures.
What is the best offset toilet flange?
Best Toilet Flange Reviews: Our Top PickProductPlumBest C54402 3-Inch by 4-Inch PVC Offset Closet Flange with Plastic…Check PriceOatey 43654 Flange Nuts, 3-Inch, WhiteCheck PriceOatey 43501 3 in. or 4 in. Level Fit White PVC Offset Closet Metal…Check PriceOatey 42777 Moss Bay Replacement Flange by OateyCheck Price6 more rows
How far out from the wall is a toilet flange?
Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.
How far can a toilet be from the soil stack?
Tie the waste line from the new toilet directly into the stack if the toilet is within six feet of the stack and the waste line is 3 inches in diameter. If the waste line is 4 inches in diameter, the toilet can be as far as 10 feet from the stack.
Can you move your toilet plumbing?
Moving the toilet is not a change to be taken lightly. But if needed, it can be accomplished with substantial plumbing work and a great deal of peripheral work, such as opening up a floor or ceiling, rerouting pipes and drain flange, and re-installing the toilet and other fixtures.
Why use offset toilet flange?
Unlike a standard flange, which is centered on the waste pipe, an offset flange is off-center—that lets you shift the location of the toilet by a couple of inches (left, right, forward or back).
How does a cheater vent work?
A cheater vent (or air admittance valve) is a vent that comes off the fixture — for example, a sink in a new powder room — and is buried in the wall. … AAVs are designed to not allow sewer gas out into your wall cavity. It’s a mechanical vent that allows necessary air into the system to help drains operate efficiently.
Can 2 toilets share a vent?
As a general rule, you will just be able to vent 2 fixtures on a toilet wet vent. The toilet is vented through the sink drain.
How far can you move a toilet with an offset flange?
For the waste water line, an offset toilet flange will allow you to move the toilet a couple of inches in any direction without having to cut a new hole in the floor or reconstruct the waste water pipe.
How much does it cost to relocate a toilet?
Cost of Moving Plumbing Fixtures The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move.
Can a toilet shower and sink share a vent?
As a general rule, you will just be able to vent 2 fixtures on a toilet wet vent. … 1) Toilet and Sink: The toilet is vented through the sink drain. The toilet drain should be 3″, the sink drain is 1.5″, the shared sink drain/toilet vent area should be 2″, and the vent going up should be 1.5″.
What happens if you don’t vent a toilet?
Poorly-vented drain lines will not be able to effectively move wastewater and solid waste out of your building. This could lead to problems such as overflowing drains, backed-up toilets, and similar plumbing issues.
Can a toilet drain have bends?
The 90 degree bends also are tough to pass through with drain cleaning equipment. The 90 degree bends also are tough to pass through with drain cleaning equipment. … Never install a 90 degree fitting under ground except when used at the base of a vertical plumbing stack.